Rear brake master cylinder PS 11C, foot operated

Can be used as a replacement for the PS12 under tank master cylinder originally fitted to V35 I and V50 II models (which is no longer available). For this conversion note that the PS11 is rod not lever actuated. Also known as Guzzi ref. AP8113502

 This part is available by special order, request a quote

 30666900 GU30666900 30 66 69 00
 3066 6900 3066.6900 30.66.69.00

Deep sump spacer made from alloy. This increases the volume of air in the crankcase and helps reduce 'heavy breathing'. The oil is also better cooled when using one of these. Finished externally in silver paint

To fit this sump spacer you will need longer sump bolts (14 x SSA06055 + 4 x SSA06090) and a pair of sump gaskets (ENA14036). You will also need a longer dipstick, see ENA28005

 Availability varies on this part, check availability

 14003240 GU14003240 14 00 32 40
 1400 3240 1400.3240 14.00.32.40

6 dog 28 tooth 5th gear

 This part is available by special order, request a quote

 14122013 GU14122013 14 12 20 13
 1412 2013 1412.2013 14.12.20.13

Brand new budget starter motor and solenoid suitable as a direct replacement for Guzzi Valeo and Bosch 8 or 9 teeth starter motors. You may need to fit hex headed neutral switch bolts on some pre 1990 models to make room for the solenoid. Our part number for the bolt is SSA06016 Please note that this item may be fitted to Loop frame models with some modifications as described in Guzziology, also see https://www.thisoldtractor.com/moto_guzzi_loopframe_starter_-_how_to_replace_the_magneti_marelli_starter_with_a_valeo.html for advice on this upgrade.

Supercedes Guzzi refs. 12730705, 14730554 and 14730705

Get a discount of £20 on this item if you part exchange your existing faulty Valeo or Bosch starter motor.

 1 in stock

 30730711 GU30730711 30 73 07 11
 3073 0711 3073.0711 30.73.07.11

Timing sensor for ignition and tacho

3 pin block connector. Used on models with the smaller 15M ECU

 1 in stock

 01721600 GU01721600 01 72 16 00
 0172 1600 0172.1600 01.72.16.00

Sump baffle or sloppage plate manufactured in the UK from stainless steel. It prevents oil starvation under heavy acceleration, especially when riding up steep hills and exends the life of the big ends. It will also help prevent 'heavy breathing', excessive oil misting and the resulting loss of oil which often occurs on big Guzzi twins when used in the upper RPM range.

To fit this sump plate you will need a pair of sump gaskets (ENA14036). This part also known as a windage plate

 This part is available by special order, request a quote

Clamp on retro style bar end mirror CNC manufactured in aluminium and finished in black, these are a high quality and stylish addition to your Guzzi and much better value than the genuine Guzzi mirrors. Classic oval shape can be flipped for fitting on either side and above or below the handlebars.

The Reverse Retro mirror is made from billet aluminum. Compact, classy and unmistakable design. Simple lines make it a sought-after Classic suitable for a range of styles. The adjustment system and anti-dazzle glass guarantee optimal versatility and comfort.

Requires 13mm on the handlebar to accommodate the mounting, with optional bar end pieces HAA00113 available to extend bars if required. You may need to redrill the locating holes in your handlebars if moving your switchgear 13mm inboard if HAA00113 is not fitted

Perfect for that classic cafe racer look

 This part is available by special order, request a quote

Splined tool for aligning clutch plates on reassembly, without this clutch alignment tool you risk damaging the intermediate plate. The tool screws into the back of the crankshaft to compress the clutch springs and align the clutch friction plates

Suitable only for later clutch centre spline type (e.g. clutch plate CLA05430). As used by the Gutsibits spanner monkeys on their bikes

 This part is due back in stock soon, call 01484 841395 to reserve yours

 30906510 GU30906510 30 90 65 10
 3090 6510 3090.6510 30.90.65.10

High performance Quadflex maintenance free Motobatt 12 volt 20Ah battery. Quadflex technology means you have two positive and two negative threaded terminals allowing maximum flexibility when installing. Motobatt absorbed gel matting batteries feature the latest absorbent glass mat technology and offer superior cranking power (240 CCA). This offers increased lifespan, higher vibration resistance and electrical performance. This battery is also leak, vibration and spill proof if installed correctly.

Supplied charged and ready to fit with terminal brackets and button head screws.
NB This battery must not be trickle charged or charged using a traditional manual charger, AGM batteries require a smart charger - we recommend ACA96000
For more information on charging AGM batteries see these FAQ's.


One year warranty on all our Motobatt batteries

Also available at the same price in black by special order - call 01484 841395 to order

Please note this part CANNOT be posted outside of the UK mainland area

 Order now and we will post your order within 7 days.

 30704500 GU30704500 30 70 45 00
 3070 4500 3070.4500 30.70.45.00

TPS for throttle body

On Cali 1100 check which TPS you have (varies according to ECU)

 1 in stock

 30530501 GU30530501 30 53 05 01
 3053 0501 3053.0501 30.53.05.01